Everything on board, from gauge set to outdoor unit

Van fit-out for air-conditioning and heating engineers

Fitting out a van for air-conditioning and heating engineers starts with your working day: your gauge set protected, your cylinders upright and secured and every fitting sorted, from the first installation to the last call-out.

Your gauge set and vacuum pump safely secured: crash-tested, even in an emergency stop
Every fitting and coupling in its own compartment: you see at once what is almost out
Cylinders upright and secured: no more rolling around in your load space
Heavy loading without straining your back: outdoor units and boilers on a pull-out drawer

→ Request a quote View solutions

Recognise this?

Your working day, without the frustrations

This is what a day looks like with a fit-out made to measure for your trade.

Your gauge set arrives in one piece, job after job

Pressure gauges and vacuum pump each travel in their own compartment. No more knocks in the bends, no measurement you no longer trust.

Every fitting and coupling in stock

Everything sorted by size in its own little compartment. You see at once what is almost out and you never stand still because that one part is missing.

Cylinders upright, secured and in their place

Nitrogen and refrigerant stand secured in their holder. Nothing rolls, nothing topples, not even on a bumpy site track.

Outdoor units and boilers without the dragging

Heavy materials slide out on a pull-out drawer to the loading door. You lift at hip height, not from the corner of your load space.

Off at once in peak heating weeks

Every call-out the same: open, grab, go. Everything is where you expect it, even when it freezes and the phone keeps ringing.

Your stock at a glance

One look in your drawers and you know what to reorder. Never bought twice again, never just without that one coupling.

Your most expensive case protected

Your gauge set safely secured, trip after trip

One knock in a bend and your manifold gauge set no longer reads correctly. Your gauge set, leak detector and vacuum pump together quickly cost a month's wages, and in a loose crate they take every bend and every emergency stop. You only notice when a measurement no longer adds up.

In our fit-out every device gets its own compartment: the gauge set in a closed drawer, the vacuum pump fixed in place, the leak detector ready to grab. Your small tools are kept in order too, the way organising tools in your van is meant to work.

Arrive, measure, move on.

Did you know… the complete fit-out is crash-tested to ECE R17? Your vacuum pump stays put in an emergency stop too.

→ Request a quote

Never without that one part again

Every fitting and coupling found in seconds

Middle of January, boiler broken at the customer's, and that one coupling is no longer in the van. In loose crates and bags you only see on the spot what has run out. Then you have to drive to the wholesaler while your customer sits in the cold and the next call-out is already ringing.

In sliding drawers with divider trays every part gets a fixed place: fittings by size, couplings by type, thermostats and small spare parts each in their own compartment. The drawers pull out fully, even when fully loaded, so you can see your whole stock at a glance. What is almost out, you top up in the evening from your warehouse.

Everything in stock, nothing bought twice.

Did you know… tradespeople with our fit-out gain up to 30 minutes per working day? In peak heating weeks that means extra call-outs per week.

→ Request a quote

Heavy and dangerous, neatly sorted

Cylinders upright and secured, outdoor units without the dragging

A nitrogen cylinder that topples in a bend makes you go quiet. And every outdoor unit or boiler also has to go in and out on site, preferably without your back locking up.

With a holder with strap, every cylinder stands upright and secured, following the rules of transporting cargo safely in your van. You place heavy appliances on a pull-out drawer system that carries up to 300 kg and stays put on its brake: you lift at hip height, right at the loading door. This is how loading heavy materials in your van should go.

Safe on the road, in one piece on site.

Did you know… our pull-out drawer system carries up to 300 kg and has a built-in brake? It stays where you put it.

→ Request a quote

Guntro solution for a generator outside the vehicle

Made to measure for your work sequence

A layout that follows your jobs and grows with your business

Installing a heat pump today, three boiler services tomorrow, a call-out the day after. No two technicians load their van the same. A standard cabinet that half fits does not really fit.

Fitting out a van for air-conditioning and heating engineers is bespoke at Guntro: we start from your work sequence and your materials and build the layout up in modules. Is another fitter joining or are you changing vans? The fit-out is bolted, not welded, and simply moves with you.

If you choose aluminium, your fit-out weighs up to 30% less than steel: more payload for appliances and cylinders and extra range. Read how to increase the range of your electric van.

Made to measure today, extended tomorrow.

Did you know… you can see the fit-out in person first?

→ Request a quote

Lightweight aluminium fit-out for more range in an electric van

For your trade

The solutions that make the difference for your trade

Fitting out a van for air-conditioning and heating engineers comes down to three things: order in your small materials, everything securely fixed and heavy loading without straining your back.